Deploying Sourcegraph executors

Executors provide a sandbox that can run resource-intensive or untrusted tasks on behalf of the Sourcegraph instance, such as:

Requirements

Executors by default use KVM-based micro VMs powered by Firecracker in accordance with our sandboxing model to isolate jobs from each other and the host. This requires executors to be run on machines capable of running Linux KVM extensions. On the most popular cloud providers, this either means running executors on bare-metal machines (AWS) or machines capable of nested virtualization (GCP).

Optionally, executors can be run without using KVM-based isolation, which is less secure but might be easier to run on common machines.

Resource Recommendations

It is recommended to set the resources based on the number of jobs an instance will process in parallel.

A single job should have the following resources available.

  • CPU: 4
  • Memory: 12GB
  • Disk: 20GB

So, if you expect an Executor instance to process up to 4 jobs in parallel, the recommended resources for the machine are

  • CPU: 16
  • Memory: 48GB
  • Disk: 80GB

The above recommended resources can be changed to fit your constraints. See below for configuring resources for a Job.

Note: the smallest machine type on AWS that can support Executors with Firecracker is c5n.metal (72 vCPU and 192GB of Memory), but concurrency can be turned up for the additional cost.

Job Configuration

The maximum number of Jobs an Executor instance can run in parallel is configured by the Environment Variable EXECUTOR_MAXIMUM_NUM_JOBS.

The CPU and Memory usage of an individual Job is configured by the Environment Variables EXECUTOR_JOB_NUM_CPUS and EXECUTOR_JOB_MEMORY. See Environment Variables for additional Environment Variables.

Note: changing CPU and Memory for jobs will affect the overall requirements for an Executor instance.

AWS

It is recommended to add the following Disk configuration in AWS.

  • IOPS: Equal to the Disk Size (so if Disk is 100GB, then IOPS is 100)
  • Throughput: 125MiB/s

Supported Infrastructures

  • Operating System: Linux-based
  • Architecture: AMD64

Firecracker Requirements

To run Executors with Firecracker enabled requires the machine to support Kernel-based Virtual Machine. See deploying Executors binary for additional information on configuring Linux Machines.

Cloud Providers

Machines on Cloud Providers have additional constraints for use with firecracker.

Configure Sourcegraph

Executors must be run separately from your Sourcegraph instance.

Since they must still be able to reach the Sourcegraph instance in order to dequeue and perform work, requests between the Sourcegraph instance and the executors are authenticated via a shared secret.

Before starting any executors, generate an arbitrary secret string (with at least 20 characters) and set it as the executors.accessToken key in your Sourcegraph instance's site-config.

Executor installation

Once the shared secret is set in Sourcegraph, you can start setting up executors that can use that access token to talk to the Sourcegraph instance.

Supported installation types

Confirm executors are working

If executor instances boot correctly and can authenticate with the Sourcegraph frontend, they will show up in the Executors page under Site Admin > Maintenance.

Executor list in UI

Using private registries

If you want to use docker images stored in a private registry that requires authentication, follow this section to configure it.

Depending on the executor runtime that is being used, different options exist for provisioning access to private container registries:

  • Through a special secret called DOCKER_AUTH_CONFIG, set in executor secrets in Sourcegraph.
  • Through the EXECUTOR_DOCKER_AUTH_CONFIG environment variable (also available as a variable in the terraform modules for executors).
  • Through the config.json file in ~/.docker. If using executors with firecracker enabled (recommended) this option is not available.

When multiple of the above options are combined, executors will use them in the following order:

  • If a DOCKER_AUTH_CONFIG executor secret is configured, that will be preferred. That is so that users can overwrite the credentials being used in their user-settings. This is the only option available in Sourcegraph Cloud.
  • If the EXECUTOR_DOCKER_AUTH_CONFIG environment variable is set, this will be used as the next option.
  • Finally, if neither of the above are set, executors will fall back to the config.json file in the user home directory of the user that is owning the executor process. NOTE: This is not available in the firecracker runtime, as the rootfs is not shared with the host.

The docker CLI supports three ways to use credentials:

Credential helpers and credential stores are only available for use with the config.json configuration option, as they require additional infrastructural changes. Thus, those options are not available on Sourcegraph Cloud.

Using static credentials

The EXECUTOR_DOCKER_AUTH_CONFIG environment variable and the DOCKER_AUTH_CONFIG secret expect a docker config with only the necessary properties set for configuring authentication. The format of this config supports multiple registries to be configured and looks like this:

{
  "auths": {
    "myregistry.example.com[:port]": {
      "auth": "base64(username:password)"
    },
    "myregistry2.example.com[:port]": {
      "auth": "base64(username:password)"
    }
  }
}

You can either create this config yourself by hand, or let docker do it for you by running:

TMP_FILE="$(mktemp -d)" bash -c 'echo "<password>" | docker --config "${TMP_FILE}" login --username "<username>" --password-stdin "<registryurl>" && cat "${TMP_FILE}/config.json" && rm -rf "${TMP_FILE}"'

You can also run the following:

echo "username:password" | base64

and then paste the result of that into a JSON string like this:

{
  "auths": {
    "myregistry.example.com[:port]": {
      "auth": "<the value from above>"
    }
  }
}

For Google Container Registry, follow this guide for how to obtain long-lived static credentials.

Configuring the auth config for use in executors

Now that the config has been obtained, it can be used for the EXECUTOR_DOCKER_AUTH_CONFIG environment variable (and terraform variable docker_auth_config) or you can create an executor secret called DOCKER_AUTH_CONFIG. Global executor secrets will be available to every execution, while user and organization level executor secrets will only be available to the namespaces executions.